2500Pa Air Pressure Pvc Hot Air Welder , Vinyl Banner Hemming Machine With Handl

Business Type
Manufacturer
Country
China

Product Detail

Splicing Machine For Banner Welding, LC 1300 Hot Small Welding Machine features: 1.no glue stitching: 502 and other glue out of the stage of history, improve the working environment of workers, improve the efficiency and quality of stitching, low-carbon environmentally friendly products, the inevitable trend of future development. 2.digital temperature control: equipped with a temperature feedback sensor, always monitor the temperature of the outlet, the use of advanced PID control technology, automatically adjust the power to make the temperature more constant. 5 . Stitching more evenly. Using zero-crossing trigger IC control, no harmonic interference. No matter how long the splicing picture, the stitching effect will not change. (Other domestic similar products: artificial knob to adjust the trigger angle control, harmonic interference is relatively large and the temperature is displayed in the output voltage value, can not reflect the real temperature value. The actual temperature changes with the input mains voltage High and low, very constant, sometimes temperature difference up to 50 above. Cheap quality but poor quality). 3.walking speed: 6-15m, according to set the temperature and the thickness of the cloth can be appropriate to adjust the line speed. 4.the temperature range: 0-700 with button according to their own circumstances can be set arbitrarily. 5.R & D production capacity: with all the core technology, quality control. R & D capacity. 6.power: 1000-2000W (set the required temperature, according to the required temperature and power automatically adjusted.) 7.hot air wind speed: 50-100% adjustable to ensure that the cloth is easier to burn, heat longer life. 8.hot air: AC fan, the wind is more powerful, longer life (more than 2000 hours), just replace the carbon brush, low cost. Specification parameters: - - - - Model | LC 3000C | Voltage | 110--230V | Frequency | 50--60Hz | Whole Power | 800--1800W | Air pressure | 2500Pa | Welding speed | 6-9 m/min | Welding thickness | 0.2--2mm | Largest welding width | 3--4cm | Cross weight | 18Kg | Net weight | 15Kg | Outside dimensions | 485285280 mm | Electric shock protection category | I | Welding temperature | 20-700 | - - - - ACCESSORIES: 1. A 10m power cable. 2. A Wrench 3. One piece of manual 4. Video CD Parts of hot air welding machine Please pay attention:In order to keep heat element,we add Automatic Dorman 1. Temperature knob 2. Wind speed knob 3. Walking speed knob 4. Reset knob 5. Temperature feedback sensor 6. operation handle 7. Wing sheath 8. Heat gun 9. Nozzle 10. Press wheel 11. Carry handrail 12. Carry handrail 13. Actual temperature 14. Set temperature 15. Walking speed 16. Turn up temperature button 17. Turn down temperature button Operation: 1.First, make the picture smooth and tight, take joiner to accurate (about 2-4cm), fixed edges with tape or glue on the ground. 2.Set temperature:connect power, turn on the temperature knob (the golden knob)until it click,and then press(for up for down). In general, the temperature is between 350-400,Or to know it the temperature is ok,we can taking some waste banners to aligned nozzle to test, If it can be melted immediately, This temperature is the one you need and to set.if not strong just increase temperature,if too hot,reduce temperature.check photo below: 3.Set wind speed:in general,we put wind speed to the largest.so just put wind speed to the Maximum is ok. 4.Set walking speed:Then turn on waling knob to adjust the speed, generally marked on the knob points to the location between 3 from 4. 5.Start welding:when actual temperature of the display screen reaches temperature that you set, we can begin to weld.put operation handrail(at end of the machine)to left,machine begin to work automatically. At begin of weld,we should use one hand to take one banner up,then put nozzle between two banners,check photo: 6. During welding,let hot air nozzle between two overlap pieces. And be make sure hot air nozzle and Rubber wheel walk in straight line.if not,please adjust by hand.check photo: 7.Finish welding:turn the walking handrail to the right ,machine stop walk,then turn off the yellow button(temperature knob),but before cut off the power,please wait until actual temperature below 50 ,then we can cut of the main power,or it would be damage heat system. 8. Dont use it in rainy day,the workplace should be dry, flat and safety of fire.The machine should have technical person to operate, it is forbid that someone use it without specific knowledge. Working voltage:110V220V. Strictly prohibited without permission disassemble,you should be responsible the result yourself.
Mr. leihualei leihualei
Contact Us Contact Details

Similar Products

Mechanical Machinery

About our Company

Business Type
Manufacturer
Products
Mechanical Machinery

Regional Suppliers

Mechanical Machinery in China

Contact Us

WuHan Kinglocor Co,.Ltd

Mr. leihualei leihualei

China

Send us a message