0.6m - 4m steel bar Reinforcing concrete welded wire mesh machine , high efficiency Welding Wire equipment
Welding Wire equipmentSpecifications:
- - - -
max input diameter | 6.5/6.0 | mm |
min output diameter | 2.2/2.0 | mm |
rotation speed | 27-168 | r/min |
each motor power | 15-22 | kw |
each weight | 1400 | kg |
- - - -
The Welding Wire equipment process:
# 1 Pretreatment, rough production line
# Steel wire pretreatment(including:Pay-off stand + Disorderly parking+New type(water clean)+ Electrolytic pickling + boron coating + High frequency drying + LZ6/560 straight-line wire drawing machine + SG800 I-spool take-up machine or none stop take-up machine
# 2 Fine drawing production line
# FX800 I-spool(or rotary ) wire pay-off machine + LZ8/400(or LZ7/400)Straight line wire drawing machine + Tension stand + Wash tank + SG630I-spool wire take-up machine
# 3 Chemical copper plating production line
# 4 Layer and packing production line
# SG630 spool pay-off machine (active type) + middle + layer winding machine
# 5 S4525 heat shrinkable packaging machine for packaging, warehousing
1. Guarantee time: one year since machine was at buyer's factory but within 18 months against B/L date.
2. Within guarantee time, if any components are broken under normal condition, we can change for free.
3. We can send our best technician to buyers factory for installation, debugging and training.
4. Complete installation instructions, circuit diagram, manual operations and machine layout.
5. Timely reply for your machine questions.
6. Main machine packed by stretch film, PLC cabinet packed by air bubble film, spare parts loaded in to box.
production equipment parameter
1. Wire material surface pre-treatment
1.1 high shelf pay-off: Put a wire rod, without motor
1.2 Scribble and automatic stop switch: wire out
of the pay-off machine through the steel ring with
a diameter of 200 mm, if a few circle wire
entwined, steel ring that was taken to the other
side, t the bottom of the stroke switch will send
signals, and the entire line emergency stop.
1.3 Repeated bending mechanical shell and
wire ball strong scrubbing device: the wire rod
at least six direction perpendicular(National
initiative)Bending heat treatment to strip iron
oxide on the surface of the wire.
Eight peeling wheel, material: ZG45 steel, hardness of HRC50, Wheel
inner diameter 115 --- 120mm.
Wheel service life of 6000 hours. After
peeling ,the wire through period of tapered hole, use wire clean ball strongly wipe the
surface of wire rod, and does not damage
the wire surface, reduce the waste into the electrolytic pickling tank, ensure the
effect of pickling, facilitate drawing; By pressure cold water irrigation and block and
impurities, rust on the surface of the wire rod export high-pressure gas blowing
device, reduce by wire out of the water.
In order to quote the right price, please provide the following information for the Mesh welding Machine:
1. Wire diameter : From mm to mm.
2. Line wire space : From mm to mm.
Cross wire space : From mm to mm.
3. Mesh width: 1200mm,1500mm, 2000mm, 2500mm, 3000mm ( customized)
4. Industrial voltage : 380V 50HZ ( Customized)
5. Do you want to weld wire mesh panel or mesh in coil ?
6. Is the auxiliary equipment following also require ?
1 800mm I-Spool take-up machine
Main transmission adopts the transmission efficiency high service life long V transmitte take form;
) With pneumatic brake and pneumatic top
Motor:15 kw variable frequency motor
Ribbon cable with screw thread, maintenance
is simple and practical
take up by 800mm I-spool
There were equipped with a mechanical locking device, at any speed, power outages, fly out to ensure that the wheel will not hurt workers
2 500mm Trunk-type Unloading Machine
The speed mach with Wire drawing machine.Single layer take-up,The surface of drum plat WC.Dia of drum is 560mm, take-up plate is 500kg, The machine have:2 take-up plate,2 wheel Barrow.Motor : 15KW
# Overall dimensions (L*W*H) 4500*840*1720(mm)
# Max packing dimension (W*H) 270*100(mm)
# Packing Speed 10-13 sets/min
# Max sealing length 200mm
# Conveyor horizontal hight 800+30(mm)
# Working pressure about 0.5Mpa
# Power source 50Hz/AC380Vthree phase five wire
# Power(Max) about 15kW